New Holland 275 Square Baler Specs

Posted on by
  1. Square Baler Texas
  2. Hesston Square Baler

Below are the general dimensions for the New Holland Hayliner 268 Baler. You can find the manual here. HAYLINER 268 BALERSPECIFICATIONS Over-all width 8' 3 ½” Over-all height 4' 1 ½” Over-all length bale chute up 15’ bale chute down 17’ 9” Wheel tread 7' 7 ½” Weight Approximately 2474 lbs. Wheel bearing Tap. Msi afterburner alternatives for mac. Hay Balers Part Diagrams New Holland 275 square baler - good condition, wire tie, 540 PTO. We have stored it inside since we have owned it. We bought this baler at a farm auction 2 years ago. The owner told us after we bought it that it is a good baler and that we would be happy with it. We bought it to keep on hand in c. NEW HOLLAND 275 For. Buyer's premium included in price USD $60.00 NH 275 SQUARE BALER W/ SHAFT.

Twine Troubleshooting

The knot did not strip off the billhook
There’s a simple knot in twine over the bale but no knot in needle twine
There’s a simple knot in the needle twine
The twine breaks at the knot
Twine in the knot is ragged

GTA 5 PS4 Cheats: Every Cheat Code for Grand Theft Auto 5 on .... New Holland Baler. About this Entry. New Holland hayliner 273 275 baler brochure was posted on October 19th, 2015 at 6.24am and is filed under holland. Going to look at a 275 baler tommorow and was wondering if they are a decent unit, owner says he put up around 1000 bales a year, are there any areas besides the knotter that i should be criticle of?, also about what years were these built and are parts still availible?, looking to put up 4-5000 bales this year and don't want to torcher myself with my mf-3 anymore. Thanks in advance steve.

There’s no knot in either twine
I’m getting a double bow knot
The twine ends are frayed or uneven
I’m running into other issues
How to pinpoint the problem
Problem: The knot did not strip off the billhook.
Excessive billhook tension can cause this; decrease tension. Or the billhook may need replacing if it’s rough, worn or bent. Is the knife arm not rubbing the billhook? Adjust or replace it. If the knife arm does not travel far enough, check lobe in cam gear and knife arm roller.
Problem: There’s a simple knot in twine over the bale but no knot in needle twine.
It could be caused by improper twine finger action; adjust to baler manual specifications. Or the needle did not place twine in twine disc, so adjust the needle to specifications and check tensioner at twine box. See if hay dogs are malfunctioning.
Baler
Problem: There’s a simple knot in the needle twine.
The twine pulled out of the twine disc. Tighten twine holder and decrease twine box tension.
Problem: The twine breaks at the knot.
Sharp edges may be in the knife arm; smooth the knife arm or replace it. Or you may have too much bale tension; decreasing tension should fix it.
Problem: Twine in the knot is ragged.
The twine holder is too tight, which doesn’t allow the billhook to borrow twine when it rotates. To repair, loosen the twine holder.
Problem: There’s no knot in either twine.
Look for a lost or sheared pin in billhook pinion gear. Inspect the trigger roller and trigger pin. Check that trigger is not bent.
Problem: I’m getting a double bow knot.
This means the billhook tension is too light or that the billhook pinion gear has too much wear. Try tightening billhook tension or replacing billhook pinion gear.
Problem: The twine ends are frayed or uneven.
Problem: I’m running into other issues.
Is the hay being baled when it’s too green or wet?

Square Baler Texas

How to pinpoint the problem.
When you find yourself at the end of your rope, trip the knotter mechanism and run the tying cycle through slowly. Most of the time the problem can be pinpointed when the tying cycle can be viewed in its entirety.
New holland 275 baler parts

Hesston Square Baler

Navigate: